Roper Washer Error Code F9E1: Long Drain Time Failure... | appliancefaults.com

Technical Background:

The MCU (Main Control Unit) monitors the drain pump's performance through current sensing. It expects the drain pump to evacuate the water within a specific time window. The F9E1 error code is triggered when the MCU detects that the drain pump is taking excessively long to empty the tub. Voltage is supplied from the MCU through the wiring harness to the drain pump. The pressure switch provides feedback to the MCU about the water level in the tub.

Symptoms:

The homeowner reports that the washing machine takes an extremely long time to drain water after a wash cycle. The clothes may still be soaking wet, and the washer may display the F9E1 error code.

Possible Causes:

Clogged drain pump filter
Kinked or blocked drain hose
Faulty drain pump
Obstruction in the tub drain line
Defective pressure switch
Control board failure

Solution:

1

Unplug the washer from the outlet.
2

Check the drain hose for kinks or obstructions. Disconnect the hose from the drainpipe and inspect for blockages.
3

Clean the drain pump filter. Locate the drain pump (usually at the bottom front or rear of the washer). Remove the access panel and unscrew the drain pump filter cap. Clean out any debris.
4

Test the drain pump. Use a multimeter to check for continuity. A reading of approximately 10-20 ohms is typical. If there is no continuity, the pump is likely defective and needs replacement. Also, using your multimeter, test for 120V AC at the pump connector during the drain cycle.
5

Verify the pressure switch operation. Locate the pressure switch and its hose. Check the hose for clogs or damage. You can also test the switch for continuity at different water levels.
6

Inspect the wire harness connections to the drain pump and control board for loose or corroded connections.
7

If all else fails, the control board may be defective and require replacement or licensed technician repair.

Safety Warning:

Always disconnect the washer from the power outlet before performing any repairs. Lock Out/Tag Out (LOTO) procedures should be followed to prevent accidental energization. Some components may retain a high voltage even after the washer is unplugged. Use caution when working near electrical components.

Prevention:

Regularly clean the drain pump filter (every 3-6 months) to prevent clogs. Avoid overloading the washer with excessive laundry. Check the drain hose periodically for kinks or damage. Use the appropriate amount of detergent to prevent excessive suds, which can impede draining.

Expert Tip:

To enter service mode, simultaneously press and hold the Start/Pause and Cycle Signal buttons for 3 seconds. This allows you to run diagnostic tests, including a drain pump test. Consult the service manual for specific codes and procedures.

Frequently Asked Questions

•How do I locate the drain pump on my specific Roper washer model?

The drain pump is typically located at the bottom front or bottom rear of the washer. You may need to remove an access panel (held in place by screws or clips) to access it. Refer to your washer's service manual for specific instructions and diagrams.

•What type of drain pump should I buy as a replacement, and where can I find it?

You need to purchase a drain pump that is compatible with your specific Roper washer model number. Check the parts diagram on the manufacturer's website or a reliable appliance parts supplier website. Enter your model number to find the correct replacement pump.

•If the drain pump is running but still not draining water, what else could be the problem?

If the drain pump is running, but water is still not draining, the impeller inside the pump might be damaged or obstructed. Even if the motor is running, a damaged impeller won't effectively move water. Also, check the tub drain line for any obstructions further down the line from the pump.

Roper Washer Error Code F9E1: Long Drain Time Failure Troubleshooting

Technical Background:

Symptoms:

Possible Causes:

Solution:

Safety Warning:

Prevention:

Expert Tip:

Frequently Asked Questions

•How do I locate the drain pump on my specific Roper washer model?

•What type of drain pump should I buy as a replacement, and where can I find it?

•If the drain pump is running but still not draining water, what else could be the problem?

Related questions

Technical Background:

Symptoms:

Possible Causes:

Solution:

Safety Warning:

Prevention:

Expert Tip: