Roper Washer Error Code F0E5: Unbalanced Load... | appliancefaults.com

Technical Background:

The F0E5 error code indicates an unbalanced load condition detected by the washer's main control unit (MCU). The MCU monitors the motor speed and vibrations during the spin cycle. If the load is excessively unbalanced, the MCU will trigger the F0E5 error and stop the cycle to prevent damage to the washer. This error can be triggered by faulty sensors or a legitimately unbalanced load.

Symptoms:

The Roper washer stops mid-cycle and displays the F0E5 error code on the control panel. The wash basket may be heavily loaded on one side, and the washer may be shaking excessively during the spin cycle.

Possible Causes:

Unevenly distributed laundry in the wash basket.
Worn or damaged suspension rods.
Faulty load sensing system (pressure switch).
Obstruction in the drain pump or drain hose.
Defective main control board (MCU).

Solution:

1

Unplug the washer from the 120V AC outlet.
2

Manually redistribute the laundry in the wash basket to ensure even distribution.
3

Inspect the suspension rods for wear, damage, or breakage. Replace if necessary. Use a 5/16-inch socket to detach and reattach.
4

Check the drain pump and drain hose for any obstructions. Clear any debris found.
5

Verify the pressure switch hose is securely connected to the tub and pressure switch. Replace the pressure switch if faulty after checking the hose.
6

Test the main control board (MCU) by checking for proper voltage at the motor control circuits. A multimeter set to AC voltage should read approximately 120V AC when the washer is attempting to spin. If voltage is absent, replace the MCU.
7

Reassemble the washer and plug it back into the 120V AC outlet. Run a test cycle to confirm the issue is resolved.

Safety Warning:

Disconnect power to the appliance before performing any repairs. Use Lock-Out/Tag-Out (LOTO) procedures to prevent accidental re-energizing of the circuit. High voltage is present in the control circuits; exercise caution when testing.

Prevention:

Avoid overloading the washer. Distribute laundry evenly in the wash basket before starting the cycle. Regularly inspect the suspension rods for wear and tear. Run an empty washer cycle with a washer cleaner every month.

Expert Tip:

Enter diagnostic mode by pressing and holding the Start/Pause button while simultaneously pressing the Temperature Up and Temperature Down buttons for 3 seconds. This allows you to run individual component tests and check for other error codes.

Frequently Asked Questions

•How do I access the suspension rods on my Roper washer?

To access the suspension rods, you typically need to remove the top panel of the washer. Disconnect power first. Then, usually there are screws at the back of the top panel that you remove, then slide the top panel back and lift it off. The suspension rods will then be visible.

•Where is the pressure switch located and how can I test it?

The pressure switch is usually located near the top of the washer cabinet, connected to the tub by a small hose. To test it, you can use a multimeter to check for continuity while blowing into the hose. A change in continuity indicates the switch is functioning.

•What type of suspension rods are compatible with my Roper washer model?

Refer to the washer's parts diagram or the manufacturer's website to determine the correct suspension rod part number. Ensure the replacement rods are specifically designed for your Roper washer model to ensure proper fit and function.

Roper Washer Error Code F0E5: Unbalanced Load Troubleshooting

Technical Background:

Symptoms:

Possible Causes:

Solution:

Safety Warning:

Prevention:

Expert Tip:

Frequently Asked Questions

•How do I access the suspension rods on my Roper washer?

•Where is the pressure switch located and how can I test it?

•What type of suspension rods are compatible with my Roper washer model?

Related questions

Technical Background:

Symptoms:

Possible Causes:

Solution:

Safety Warning:

Prevention:

Expert Tip: