GE Profile UltraFast Combo Error 353: Lint Filter... | appliancefaults.com

Technical Background:

The GE Profile UltraFast Combo uses a lint filter sensor to detect the presence of excessive lint buildup. The sensor is typically a thermistor or optical sensor that monitors the temperature or light level in the lint filter housing. When the sensor detects excessive lint, it sends a signal to the main control unit (MCU). The MCU then triggers error code 353 and halts the drying cycle. The voltage path is typically a 5V DC circuit with a pull-up resistor. Resistance changes in the thermistor indicate lint buildup.

Symptoms:

US homeowners report the GE Profile UltraFast Combo displaying error code 353. The machine may stop mid-cycle, and a notification regarding lint filter residue cleaning is displayed on the control panel. Some users might also notice a burning smell or reduced drying performance.

Possible Causes:

Excessive lint buildup in the lint filter housing.
Blockage in the exhaust duct leading from the lint filter.
Faulty lint filter sensor.
Damaged wiring harness connecting the lint filter sensor to the main control board.
MCU software glitch.
Incorrect vent duct system (excessive length or bends).

Solution:

1

Disconnect power to the unit at the breaker panel. Verify 0V AC at the wall outlet using a multimeter.
2

Locate the lint filter housing, typically near the dryer drum opening.
3

Remove the lint filter and thoroughly clean it with a soft brush and vacuum.
4

Inspect the lint filter housing for residue buildup. Use a narrow brush or vacuum crevice tool to remove any accumulated lint.
5

Check the exhaust duct connected to the lint filter housing for obstructions. Disconnect the duct and visually inspect it for blockages. Clear any obstructions.
6

Locate the lint filter sensor. Use a multimeter to test the sensor for continuity. Refer to the service manual for the correct resistance value. Replace if faulty.
7

Inspect the wiring harness connecting the lint filter sensor to the main control board for damage. Repair or replace as needed.
8

Reassemble all components and restore power to the unit. Run a test cycle to verify the error code is cleared.

Safety Warning:

Always disconnect power to the appliance at the breaker panel before performing any repairs. Lock Out Tag Out (LOTO) procedures should be followed to prevent accidental re-energizing of the circuit. Be aware of potential shock hazards from 120V AC components.

Prevention:

Clean the lint filter after every load. Periodically inspect and clean the exhaust duct, at least every 6 months. Use dryer sheets sparingly, as they can contribute to lint buildup. Ensure proper ventilation of the laundry room.

Expert Tip:

After cleaning the lint filter and exhaust duct, run the dryer in service mode. The service mode sequence is: Press and hold the Start/Pause button, then press the Temp and Signal buttons simultaneously for 3 seconds. Navigate to the error clearing menu and clear the 353 error code.

Frequently Asked Questions

•What is the resistance range of the lint filter sensor at room temperature?

The resistance range of the lint filter sensor is typically between 10k and 20k ohms at 70 degrees Fahrenheit. Refer to the service manual for the exact specification for your model.

•Where is the main control board located in the GE Profile UltraFast Combo?

The main control board is typically located behind the control panel, at the top of the appliance. You will need to remove the control panel to access it. Disconnect power before accessing.

•What is the recommended length and bend radius for the exhaust duct?

The recommended maximum length for the exhaust duct is 25 feet, with no more than two 90-degree bends. Each 90-degree bend reduces the maximum duct length by 5 feet. Ensure a minimum bend radius of 5 inches.

GE Profile UltraFast Combo Error 353: Lint Filter Residue Cleaning Guide

Technical Background:

Symptoms:

Possible Causes:

Solution:

Safety Warning:

Prevention:

Expert Tip:

Frequently Asked Questions

•What is the resistance range of the lint filter sensor at room temperature?

•Where is the main control board located in the GE Profile UltraFast Combo?

•What is the recommended length and bend radius for the exhaust duct?

Related questions

Technical Background:

Symptoms:

Possible Causes:

Solution:

Safety Warning:

Prevention:

Expert Tip: