Frigidaire Affinity Washer: Clothes Still Dripping Wet... | appliancefaults.com

Technical Background:

The washer's Main Control Unit (MCU) controls the drain pump and spin cycle based on signals from the water level sensor, lid switch/door lock, and motor speed sensor. Voltage is sent to the drain pump and then the motor during the spin cycle. If any of these components fail, the MCU may not initiate or complete the spin cycle, leaving the clothes wet.

Symptoms:

The Frigidaire Affinity washer completes its cycle, but the clothes remain soaking wet. The spin cycle seems weak or nonexistent. The washer may display an error code, or it may not. The homeowner reports that the clothes are dripping wet even after the spin cycle has finished.

Possible Causes:

Clogged drain pump filter
Kinked or blocked drain hose
Faulty drain pump
Defective lid switch or door lock assembly
Worn drive belt (on belt-driven models)
Malfunctioning pressure switch or water level sensor

Solution:

1

Unplug the washer from the 120V AC power outlet.
2

Locate and clean the drain pump filter, typically found behind a small access panel at the front of the machine. Remove any lint, debris, or small objects.
3

Inspect the drain hose for kinks, clogs, or obstructions. Disconnect the hose from the drainpipe and the washer to clear any blockages. Use a garden hose to flush it out.
4

Test the drain pump: With the washer unplugged, disconnect the wires to the drain pump. Using a multimeter, check for continuity across the pump terminals. If there's no continuity, the pump is likely faulty. If continuity is present, reconnect the pump wires and plug the washer back in briefly to see if the pump activates during the drain cycle. Be careful to avoid electrical shock.
5

Check the lid switch or door lock assembly. Use a multimeter to check for continuity when the lid/door is closed. Replace if defective.
6

Inspect the drive belt (if applicable). A worn or broken belt can prevent the drum from spinning at full speed. Replace the belt if it shows signs of wear or damage.
7

Verify the pressure switch or water level sensor is operating correctly. You may need a service manual to test this component. The water level should not be higher than expected at the spin cycle.

Safety Warning:

Always unplug the washer before performing any repairs. Lockout/Tagout (LOTO) procedures should be followed to prevent accidental power-up during servicing. Exercise caution when working with electrical components. High voltage is present when the machine is plugged in.

Prevention:

Regularly clean the drain pump filter (every 3 months). Avoid overloading the washer. Use the correct amount of detergent. Check the drain hose for kinks periodically.

Expert Tip:

Many Frigidaire washers have a diagnostic mode. To enter service mode, simultaneously press and hold the Start/Pause and Option buttons for 3 seconds. Consult the service manual to interpret any error codes displayed.

Frequently Asked Questions

•How do I access the drain pump filter on my Frigidaire Affinity washer?

The drain pump filter is usually located behind a small access panel at the bottom front of the washer. You might need a flathead screwdriver to open the panel. Have a towel ready to catch any water that may spill out.

•What is the proper way to test the drain pump with a multimeter?

First, unplug the washer. Disconnect the wires from the drain pump. Set your multimeter to the continuity setting (usually symbolized by a diode or speaker icon). Place the multimeter probes on the two terminals of the drain pump. A reading of continuity (a sound or a low resistance value) indicates the pump is likely good, but not guaranteed. The absence of continuity means the pump is likely bad.

•Where can I find a replacement drain pump for my Frigidaire Affinity washer?

You can find replacement drain pumps at most appliance parts retailers, both online and in brick-and-mortar stores. Be sure to have your washer's model number handy to ensure you order the correct part. Also, search for 'Frigidaire Affinity washer parts'.

Frigidaire Affinity Washer: Clothes Still Dripping Wet After Spin Cycle - Troubleshooting Guide

Technical Background:

Symptoms:

Possible Causes:

Solution:

Safety Warning:

Prevention:

Expert Tip:

Frequently Asked Questions

•How do I access the drain pump filter on my Frigidaire Affinity washer?

•What is the proper way to test the drain pump with a multimeter?

•Where can I find a replacement drain pump for my Frigidaire Affinity washer?

Related questions

Technical Background:

Symptoms:

Possible Causes:

Solution:

Safety Warning:

Prevention:

Expert Tip: