Speed Queen Washing Machine Clothes Dripping Wet:... | appliancefaults.com

Technical Background:

The Speed Queen washing machine relies on its Main Control Unit (MCU) to manage the drain and spin cycles. The MCU sends a 120V AC signal to the drain pump motor to evacuate water. Simultaneously, it activates the motor to initiate the spin cycle. The lid switch or lid lock provides feedback to the MCU, ensuring the machine operates safely only when the lid is closed.

Symptoms:

The washing machine completes its cycle, but the clothes are still dripping wet. The spin cycle may be weak or nonexistent, and water may remain in the tub after the cycle is finished.

Possible Causes:

Clogged drain pump or drain hose
Worn or loose drive belt (if applicable on older models)
Defective lid switch or lid lock mechanism
Failed or failing drain pump motor
Obstruction in the tub drain outlet
Malfunctioning electronic control board (MCU)

Solution:

1

Unplug the washing machine from the outlet.
2

Inspect the drain hose for kinks, clogs, or obstructions. Disconnect the hose from the drain standpipe and check for free flow.
3

Locate and access the drain pump (usually behind an access panel at the bottom front or rear of the washer). Remove any debris or obstructions from the pump impeller. Use a 1/4-inch nut driver to remove the access panel.
4

Use a multimeter to test the drain pump motor for continuity. A typical reading should be between 3 and 6 ohms.
5

Check the lid switch or lid lock mechanism for proper function. Use a multimeter to test for continuity when the lid is closed. Ensure the lid lock is engaging properly.
6

On belt-driven models, inspect the drive belt for wear, cracks, or looseness. Replace if necessary.
7

If all other components test okay, the electronic control board (MCU) may be faulty and require replacement. Consult a qualified technician.

Safety Warning:

Disconnect power to the appliance before performing any repairs. Use Lock-Out/Tag-Out (LOTO) procedures to prevent accidental re-energizing of the circuit. High voltage components are present; exercise caution when testing electrical circuits.

Prevention:

Regularly clean the lint filter and inspect the drain hose for kinks or clogs. Avoid overloading the washing machine. Periodically run an empty wash cycle with a washing machine cleaner to prevent buildup in the tub and drain system.

Expert Tip:

Speed Queen washers have a diagnostic mode. To access it, consult the service manual specific to your model. This mode allows you to run individual component tests, including the drain pump and spin motor. This speeds up fault isolation.

Frequently Asked Questions

•How do I access the drain pump on my Speed Queen washer?

The drain pump is typically located behind an access panel at the bottom front or rear of the washer. You may need a 1/4-inch nut driver or a Phillips head screwdriver to remove the panel. Refer to your washer's service manual for specific instructions.

•What is the proper resistance reading for a Speed Queen drain pump motor?

A healthy Speed Queen drain pump motor typically exhibits a resistance between 3 and 6 ohms when tested with a multimeter. An open circuit (infinite resistance) or a very low resistance (near zero) indicates a faulty motor.

•How do I check the lid switch on my Speed Queen washer?

With the washer unplugged, locate the lid switch. Use a multimeter set to continuity testing. Manually depress the lid switch and check if the meter shows continuity (a closed circuit). If the meter does not show continuity when the switch is depressed, the switch is likely faulty.

Speed Queen Washing Machine Clothes Dripping Wet: Troubleshooting and Repair

Technical Background:

Symptoms:

Possible Causes:

Solution:

Safety Warning:

Prevention:

Expert Tip:

Frequently Asked Questions

•How do I access the drain pump on my Speed Queen washer?

•What is the proper resistance reading for a Speed Queen drain pump motor?

•How do I check the lid switch on my Speed Queen washer?

Related questions

Technical Background:

Symptoms:

Possible Causes:

Solution:

Safety Warning:

Prevention:

Expert Tip: