Roper Washer Error Code CLr FLtr: Troubleshooting Guide... | appliancefaults.com

Technical Background:

The Main Control Unit (MCU) monitors the water level and drain pump function. If the MCU detects a blockage or failure in the drain system, it triggers the “CLr FLtr” error code. This often involves a low voltage signal from the pressure switch (indicating water not draining) or a lack of current draw from the drain pump motor. The MCU relies on feedback from the drain pump circuit and pressure switch (typically 5V DC signals) to determine if the drain system is functioning correctly.

Symptoms:

The Roper washer displays the “CLr FLtr” error code. The washer may not drain properly, or it may stop mid-cycle.

Possible Causes:

Blocked drain pump filter
Clogged drain hose
Faulty drain pump
Defective pressure switch
Issue with the Main Control Unit (MCU)

Solution:

1

Disconnect power to the washer at the breaker panel.
2

Locate the drain pump filter access panel, usually at the bottom front of the washer. You may need a flat-head screwdriver.
3

Open the access panel and carefully remove the drain pump filter, being prepared for water spillage. Have a bucket and towels ready.
4

Clean the drain pump filter thoroughly, removing any lint, debris, or obstructions.
5

Inspect the drain hose for kinks or clogs. Disconnect the hose at both ends (washer and drain pipe) and flush it out with water, using a garden hose if needed.
6

Reinstall the drain pump filter and secure the access panel.
7

Restore power to the washer and run a test cycle to verify the error code is resolved. Monitor the drain pump during the cycle. If the error persists, you may need to test the drain pump windings with a multimeter for continuity (expect a reading around 10-20 ohms) and also confirm 120V AC is reaching the pump when activated.

Safety Warning:

Disconnect power to the washer at the breaker panel before performing any repairs. Use Lock-Out/Tag-Out (LOTO) procedures to prevent accidental power-up during maintenance. Be aware of potential water spillage when removing the drain pump filter. High voltage is present when the unit is energized.

Prevention:

Regularly clean the drain pump filter (every 1-3 months) to prevent blockages. Avoid overloading the washer and use appropriate amounts of detergent.

Expert Tip:

Some Roper washers have a service mode. Consult the service manual (available online) for the specific model. Typically, pressing and holding a combination of buttons (e.g., Start/Pause and Cycle Signal) for 3 seconds will enter service mode, allowing for diagnostic tests of individual components, including the drain pump. This can help pinpoint the source of the problem.

Follow-up Questions:

Frequently Asked Questions

•How do I access the drain pump filter on my specific Roper washer model?

The drain pump filter is usually located behind a small access panel at the bottom front of the washer. The owner's manual will show the exact location and removal procedure.

•How do I test the drain pump to see if it's working properly?

First, visually inspect the pump for any damage. With the washer unplugged, use a multimeter to check the pump windings for continuity. Also, when the washer is running and attempting to drain, carefully measure the voltage at the pump connector (120V AC).

•Where can I find the service manual for my Roper washer model?

The service manual can often be found online by searching for "Roper washer service manual" along with your specific model number. Sites like AppliancePartsPros.com or RepairClinic.com are good resources.

Roper Washer Error Code CLr FLtr: Troubleshooting Guide - Blocked Pump Filter

Technical Background:

Symptoms:

Possible Causes:

Solution:

Safety Warning:

Prevention:

Expert Tip:

Frequently Asked Questions

•How do I access the drain pump filter on my specific Roper washer model?

•How do I test the drain pump to see if it's working properly?

•Where can I find the service manual for my Roper washer model?

Related questions

Technical Background:

Symptoms:

Possible Causes:

Solution:

Safety Warning:

Prevention:

Expert Tip: